Наръчник Black and Decker AST1XC Ударна бормашина

Наръчник

4

ENGLISH

Warning! Never change the direction of rotation while

the motor is running.

Selecting the drilling mode

• For drilling in masonry, set the drilling mode selector

(4) to the position.

• For drilling in other materials and for screwdriving,

set the drilling mode selector (4) to the

position.

Switching on and off (fig. E)

• To switch the tool on, press the variable speed switch

(1). The tool speed depends on how far you press

the switch. As a general rule, use low speeds for

large diameter drill bits and high speeds for smaller

diameter drill bits.

• For continuous operation, press the lock-on button

(2) and release the variable speed switch. This

option is available only at full speed.

• To switch the tool off, release the variable speed

switch. To switch the tool off when in continuous

operation, press the variable speed switch once

more and release it.

Accessories

The performance of your tool depends on the accessory

used. Black & Decker and Piranha accessories are

engineered to high quality standards and designed to

enhance the performance of your tool.

By using these accessories you will get the very best

from your tool.

Maintenance

Your tool has been designed to operate over a long period

of time with a minimum of maintenance. Continuous

satisfactory operation depends upon proper tool care

and regular cleaning.

Mains plug replacement (U.K. & Ireland only)

If a new mains plug needs to be fitted:

• Safely dispose of the old plug.

• Connect the brown lead to the live terminal in the

new plug.

• Connect the blue lead to the neutral terminal.

Warning! No connection is to be made to the earth

terminal. Follow the fitting instructions supplied with good

quality plugs. Recommended fuse: 5 A.

Protecting the environment

Separate collection. This product must not be

disposed of with normal household waste.

Should you find one day that your Black & Decker product

needs replacement, or if it is of no further use to you, do

not dispose of it with household waste. Make this product

available for separate collection.

Additional safety instructions for hammer drills

• Wear ear protectors. Exposure to noise can cause

hearing loss.

• Use auxiliary handles supplied with the tool. Loss

of control can cause personal injury.

• Preferably wear a dust mask.

Electrical safety

This tool is double insulated; therefore no

earth wire is required. Always check that the

power supply corresponds to the voltage on

the rating plate.

Features

This tool includes some or all of the following features.

1. Variable speed switch

2. Lock-on button

3. Forward/reverse switch

4. Drilling mode selector

5. Side handle

6. Chuck

Assembly

Warning! Before assembly, make sure that the tool is

switched off and unplugged.

Fitting the side handle (fig. A)

• Turn the grip (7) counterclockwise until you can

slide the side handle (5) onto the front of the tool as

shown.

• Rotate the side handle into the desired position.

• Tighten the side handle by turning the grip

clockwise.

Fitting a drill bit or screwdriver bit (fig. B)

• Open the chuck by turning the front part (8) with one

hand while holding the rear part (9) with the other.

• Insert the bit shaft (10) into the chuck and firmly

tighten the chuck.

Removing and refitting the chuck (fig. C)

• Open the chuck as far as possible.

• Remove the chuck retaining screw (11), located in

the front part of the chuck, by turning it clockwise

using a screwdriver.

• Tighten an Allen key (12) into the chuck and strike

it with a hammer as shown.

• Remove the Allen key.

• Remove the chuck by turning it counterclockwise.

• To refit the chuck, screw it onto the spindle and

secure it with the chuck retaining screw.

Use

Warning! Before drilling into walls, floors or ceilings,

check for the location of wiring and pipes.

Selecting the direction of rotation (fig. D)

• For drilling and for tightening screws, place the

forward/ reverse switch (3) in the neutral position.

• For loosening screws or removing a jammed drill bit,

turn the forward/reverse switch (3) to the left.

оценка

Повече за това ръководство

Разбираме, че е хубаво да имате хартиено ръководство за вашия Black and Decker AST1XC Ударна бормашина. Винаги можете да изтеглите ръководството от нашия уебсайт и да го отпечатате сами. Ако искате да имате оригинално ръководство, препоръчваме ви да се свържете с Black and Decker. Може да са в състояние да предоставят оригинално ръководство. Търсите ли ръководството на вашия Black and Decker AST1XC Ударна бормашина на различен език? Изберете предпочитания от вас език на началната ни страница и потърсете номера на модела, за да видите дали го предлагаме.

Спецификации

Всички ръководства за Black and Decker Ударни бормашини
Още ръководства на Ударни бормашини

Често задавани въпроси за Black and Decker AST1XC Ударна бормашина

Нашият екип за поддръжка търси полезна информация за продукта и отговори на често задавани въпроси. Ако откриете неточност в нашите често задавани въпроси, моля, уведомете ни, като използвате нашата форма за контакт.

Свързани продукти

Наръчник

Bosch GBH 2-26 DFR Professional Ударна бормашина

Наръчник

Hikoki DV 16V Ударна бормашина

Наръчник

FF Group ID 550 Plus Ударна бормашина

Наръчник

Casals VT50REAM Ударна бормашина

Наръчник

Bosch GSB 780 Professional Ударна бормашина

Наръчник

Sparky BU2 250 Ударна бормашина

Наръчник

Bosch GBM 10 RE Ударна бормашина

Наръчник

AEG SBE 600 R Ударна бормашина

Свързани категории