Наръчник Skil 7126 AD Delta Sander Шлайф

Наръчник

10

- for sanding of rough or plain wood use medium grit

sizes (80, 100, 120)

- for smoothing of wood and surfaces with old paint as

well as for nishing of bare wood use ne grit sizes

(180, 240, 320)

• Use dierent grit sizes when the working surface is

rough:

- start sanding with coarse or medium grit

- nish with ne grit

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially ventilation

slots D

2

)

- remove adhering sanding dust with a brush

! disconnect the plug before cleaning

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should

be carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of the

tool are listed on www.skil.com)

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC

on waste of electric and electronic equipment and

its implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol

5

will remind you of this when the need for

disposing occurs

NOISE / VIBRATION

• Measured in accordance with EN 62841 the sound

pressure level of this tool is 82.5 dB(A) and the sound

power level 93.5 dB(A) (standard deviation: 3 dB), and

the vibration 10.1 m/s² (triax vector sum; uncertainty

K = 1.5 m/s²)

• The vibration emission level has been measured in

accordance with a standardised test given in EN 62841;

it may be used to compare one tool with another and as

a preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintained accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! 

maintaining the tool and its accessories, keeping

your hands warm, and organizing your work

patterns

• On/o switch

- switch on/o the tool by pushing switch B

2

forward/

backwards

! before the sanding surface reaches the workpiece,

you should switch on the tool

! 

the workpiece

• Speed control

8

For optimal sanding results on dierent materials

- with wheel C

2

you can set the desired sanding speed

- before starting a job, nd the optimal speed and grit by

testing out on spare material

• Holding and guiding the tool

! 

coloured grip area(s)

9

- guide the tool parallel to the working surface

! do not apply too much pressure on the tool; let the

sanding surface do the work for you

- do not tilt the tool in order to avoid unwanted sanding

marks

- keep ventilation slots D

2

uncovered

• Turnable foot

q

! unplug tool before removing/mounting backing

pads

! pad screw H becomes hot during use; do not

touch it before it has cooled down

- for changing front tip of sanding sheet/sanding foot

when it is worn or damaged

- for changing foot position depending on working

surface (see: Application advice)

- take hex key E from storage F

- remove VELCRO sanding sheet G

- remove pad screw H with hex key E

- turn backing pad J 60° or 120°

- fasten pad screw H with hex key E

! 

pad screw H

• Mounting special sanding attachment K (not standard

included)

w

- remove VELCRO sanding sheet G

2

- remove pad screw H with hex key E

- mount attachment K onto the tool and fasten it with pad

screw H

- mount corresponding VELCRO sanding sheet to

sanding attachment

APPLICATION ADVICE

• Use the tool with the delta-tip pointing forward for corners

and edges

e

• Use the tool with the at side pointing forward for long

strokes on at surfaces

r

• Use the tool with special sanding attachment K

2

for

narrow and other hard-to-reach places

t

• When the foampad of the delta-tip is worn or damaged at

the top, you may extend its service life twice by turning it

120° (also applicable to delta sanding sheet)

q

• Never use the same sanding sheet for wood and metal

• Recommended sanding sheet grits:

- for removing paint and for sanding of extremely rough

wood use coarse grit sizes (40, 60)

оценка

Повече за това ръководство

Разбираме, че е хубаво да имате хартиено ръководство за вашия Skil 7126 AD Delta Sander Шлайф. Винаги можете да изтеглите ръководството от нашия уебсайт и да го отпечатате сами. Ако искате да имате оригинално ръководство, препоръчваме ви да се свържете с Skil. Може да са в състояние да предоставят оригинално ръководство. Търсите ли ръководството на вашия Skil 7126 AD Delta Sander Шлайф на различен език? Изберете предпочитания от вас език на началната ни страница и потърсете номера на модела, за да видите дали го предлагаме.

Спецификации

Всички ръководства за Skil Делта Сандърс
Още ръководства на Делта Сандърс

Често задавани въпроси за Skil 7126 AD Delta Sander Шлайф

Нашият екип за поддръжка търси полезна информация за продукта и отговори на често задавани въпроси. Ако откриете неточност в нашите често задавани въпроси, моля, уведомете ни, като използвате нашата форма за контакт.

Свързани продукти

Наръчник

Skil 7115 AA Delta Sander Шлайф

Наръчник

Skil 3720 CC Delta Sander Шлайф

Наръчник

Skil 7125 AA Delta Sander Шлайф

Наръчник

Skil 7260 DA Delta Sander Шлайф

Наръчник

Skil 3720 FB Delta Sander Шлайф

Наръчник

Skil 7207 AK Delta Sander Шлайф

Наръчник

Skil 7261 AA Delta Sander Шлайф

Наръчник

Skil 7261 AB Delta Sander Шлайф

Свързани категории