Наръчник BEKO WMI 71241 Пералня

Наръчник

3

EN

Appropriate installation location

• Placethemachineonarigidfloor.Donotplaceit

on a long pile rug or similar surfaces.

• Totalweightofthewashingmachineandthe

dryer-withfullload-whentheyareplaced

ontopofeachotherreachestoapprox.180

kilograms. Place the product on a solid and flat

floor that has sufficient load carrying capacity!

• Donotplacetheproductonthepowercable.

• Donotinstalltheproductatplaceswhere

temperaturemayfallbelow0ºC.

• Placetheproductatleast1cmawayfromthe

edges of other furniture.

Removing packaging reinforcement

Tilt the machine backwards to remove the

packaging reinforcement. Remove the packaging

reinforcement by pulling the ribbon.

Removing the transportation locks

A

 Donotremovethetransportationlocksbefore

taking out the packaging reinforcement.

A

Remove the transportation safety bolts before

operating the washing machine, otherwise, the

product will be damaged.

1.Loosenalltheboltswithaspanneruntilthey

rotate freely (C).

2. Remove transportation safety bolts by turning

them gently.

3.AttachtheplasticcoverssuppliedintheUser

Manual bag into the holes on the rear panel. (P)

C

Keep the transportation safety bolts in a safe

place to reuse when the washing machine

needs to be moved again in the future.

C

Never move the product without the

transportation safety bolts properly fixed in

place!

Connecting water supply

C

 Thewatersupplypressurerequiredtorun

theproductisbetween1to10bars(0.1–10

MPa).Itisnecessarytohave10–80litersof

water flowing from the fully open tap in one

minute to have your machine run smoothly.

Attach a pressure reducing valve if water

pressure is higher.

C

 Ifyouaregoingtousethedoublewater-inlet

productasasingle(cold)water-inletunit,you

must install the supplied stopper to the hot

water valve before operating the product.

(Applies for the products supplied with a blind

stopper group.)

C

 Ifyouwanttousebothwaterinletsofthe

product, connect the hot water hose after

removing the stopper and gasket group from

the hot water valve. (Applies for the products

supplied with a blind stopper group.)

A

Models with a single water inlet should not be

connectedtothehotwatertap.Insuchacase

the laundry will get damaged or the product will

switch to protection mode and will not operate.

A

 Donotuseoldorusedwaterinlethoseson

thenewproduct.Itmaycausestainsonyour

laundry.

1.Connectthespecialhosessuppliedwiththe

product to the water inlets on the product. Red

hose(left)(max.90ºC)isforhotwaterinlet,

bluehose(right)(max.25ºC)isforcoldwater

inlet.

A

Ensure that the cold and hot water connections

are made correctly when installing the product.

Otherwise,yourlaundrywillcomeouthotatthe

end of the washing process and wear out.

2. Tighten all hose nuts by hand. Never use a

wrench when tightening the nuts.

3.Openthetapscompletelyaftermakingthehose

connection to check for water leaks at the

connectionpoints.Ifanyleaksoccur,turnoff

the tap and remove the nut. Retighten the nut

carefully after checking the seal. To prevent

water leakages and damages caused by them,

keep the taps closed when the machine is not

in use.

Connecting to the drain

• Theendofthedrainhosemustbedirectly

connected to the wastewater drain or to the

washbasin.

A

Your house will be flooded if the hose comes

out of its housing during water discharge.

Moreover, there is risk of scalding due to

high washing temperatures! To prevent such

situations and to ensure smooth water intake

and discharge of the machine, fix the end of the

discharge hose tightly so that it cannot come

out.

• Thehoseshouldbeattachedtoaheightofat

least40cm,and100cmatmost.

• Incasethehoseiselevatedafterlayingitonthe

floor level or close to the ground (less than

40cmabovetheground),waterdischarge

becomes more difficult and the laundry may

come out excessively wet. Therefore, follow the

оценка

Повече за това ръководство

Разбираме, че е хубаво да имате хартиено ръководство за вашия BEKO WMI 71241 Пералня. Винаги можете да изтеглите ръководството от нашия уебсайт и да го отпечатате сами. Ако искате да имате оригинално ръководство, препоръчваме ви да се свържете с BEKO. Може да са в състояние да предоставят оригинално ръководство. Търсите ли ръководството на вашия BEKO WMI 71241 Пералня на различен език? Изберете предпочитания от вас език на началната ни страница и потърсете номера на модела, за да видите дали го предлагаме.

Спецификации

Всички ръководства за BEKO Перални машини
Още ръководства на Перални машини

Често задавани въпроси за BEKO WMI 71241 Пералня

Нашият екип за поддръжка търси полезна информация за продукта и отговори на често задавани въпроси. Ако откриете неточност в нашите често задавани въпроси, моля, уведомете ни, като използвате нашата форма за контакт.

Свързани продукти

Наръчник

BEKO EV 6800+ Пералня

Наръчник

BEKO WML 15060 E Пералня

Наръчник

BEKO WUE 7612 BS Пералня

Наръчник

BEKO BM1WFSU36223WPBB Пералня

Наръчник

BEKO WTV 7522 XCW Пералня

Наръчник

BEKO BM3WFSU37213WA Пералня

Наръчник

BEKO WML 15060 KL Пералня

Наръчник

BEKO WMY 61283 MB3 Пералня

Свързани категории