Наръчник Parkside IAN 273439 заварчик

Наръчник

11 GB

Safety information / Assembling the welding shield / Preparing to weld

Preparing to weld / Welding / Overheat protection

Note: If the tensioning force of the electrode

holder

5

and the earth terminal

4

subsides,

replace immediately.

Connect the electric cables.

Set the ON / OFF switch

2

to the “ON“ posi-

tion. The current indicator will light up when

operation starts.

To end operation, set the ON / OFF switch

2

to the auf “OFF“ position.

Note: The yellow indicator light

6

lighting

up indicates overheating. The electric circuit will

automatically be broken. Operation will end.

Attach the earth terminal

4

directly to the

work piece or to the pad on which the work

piece is placed.

Note: Ensure direct contact to the work piece.

Thus avoid painted surfaces and / or insulation.

Note: Always use the welding shield

7

whilst

welding. It protects the eyes from the light beam

emitted by the arc, yet allows for a clear view

of the work piece.

Welding

After making all the electrical connections for the

power supply and for the welding circuit, proceed

as follows:

Insert the uncoated end of the electrode into

the electrode holder

5

and connect the earth

terminal

4

to the work piece. Be sure the

electrical contact is good.

The device features a latch for setting the plate

thickness. Switch on the device by setting the

ON / OFF switch

2

to the “ON“ position. Then

use the hand wheel

3

to select the electrode

thickness: For 1.6 or 2.0 mm electrodes set the

hand wheel

3

to position 1.6 / 2.0. For 2 mm

electrodes set the hand wheel

3

to position 2.5.

Hold the welding shield

7

in front of your face

and guide the tip of the electrode over the work

piece as if trying to light a match. This is the best

method for sparking the arc.

Use a test piece to check if you selected the

correct electrode and current.

ATTENTION!

Do not dab the work piece with the electrode. It

could become damaged and make it more difficult to

spark the arc. Once the arc is sparked, try to main-

tain a distance to the work piece appropriate for the

selected electrode diameter. Keep the distance as

consistent as possible whilst welding. The electrode

grade in the work flow direction should be 20–30

degrees.

ATTENTION!

Always use forceps to dispose of used electrodes or

move hot work pieces. Please remember to always

place the electrode holder onto an insulating pad

after welding.

Only remove slag once the seam has cooled. If

continuing to weld on an interrupted weld seam,

first remove the slag at the start of weld.

ATTENTION!

Welding produces heat. The welding equipment

must therefore be operated in open loop after use

for at least half an hour. Or alternatively allow the

equipment to cool off for one hour. Only pack up

and store the equipment once the equipment tem-

perature has normalised.

Switch the equipment off by setting the ON /

OFF switch

2

to the “OFF“ position.

Overheat protection

The welding equipment features overheat protection.

If the overheat protection is triggered, the control

light

6

will light up. Allow the welding equipment

to cool down for a while.

PESG 120 B2 (with AC 230 V 50 Hz power plug):

The supply line fuses to the mains sockets must meet

the requirements (VDE 0100). Earthed wall sockets

must be protected with max. 16 A (model and tech-

nical data: NDM1-63, AC 230 / 400 V C16.

IEC 60898.time lag. Manufacturer: Nader) (fuses

or line circuit breaker). Higher fuse ratings can result

in burnt wires or fire damage to the building.

273439_Elektro-Schweissgeraet_PESG 120 B2_content_HR_RO_BG_GR.indd 11 18.01.16 16:38

оценка

Повече за това ръководство

Разбираме, че е хубаво да имате хартиено ръководство за вашия Parkside IAN 273439 заварчик. Винаги можете да изтеглите ръководството от нашия уебсайт и да го отпечатате сами. Ако искате да имате оригинално ръководство, препоръчваме ви да се свържете с Parkside. Може да са в състояние да предоставят оригинално ръководство. Търсите ли ръководството на вашия Parkside IAN 273439 заварчик на различен език? Изберете предпочитания от вас език на началната ни страница и потърсете номера на модела, за да видите дали го предлагаме.

Спецификации

Всички ръководства за Parkside Заварчици
Още ръководства на Заварчици

Често задавани въпроси за Parkside IAN 273439 заварчик

Нашият екип за поддръжка търси полезна информация за продукта и отговори на често задавани въпроси. Ако откриете неточност в нашите често задавани въпроси, моля, уведомете ни, като използвате нашата форма за контакт.

Свързани продукти

Наръчник

Parkside PMPS 200 B1 заварчик

Наръчник

Parkside IAN 286510 заварчик

Наръчник

Parkside IAN 314788 заварчик

Наръчник

Parkside IAN 103333 заварчик

Наръчник

Parkside IAN 70383 заварчик

Наръчник

Parkside IAN 306962 заварчик

Наръчник

Parkside IAN 310867 заварчик

Наръчник

Parkside IAN 315795 заварчик

Свързани категории